Built on the 4100’s foundation, The Bosch REAXX exhibits similar performance with a few improvements. Despite what we’ve seen online, the REAXX did seem to have better cutting power than the 4100. (see Editor’s Note above) The narrow throat plate opening also gave it much better dust collection, allowing only the finest material to make its way out. It shares the top ranking gravity rise stand with the 4100.
Previous buyers said they were at a loss to find materials that the Jet couldn’t cut! They said it went like butter, with no lag whatsoever, and almost no vibration at all. Reviewers raved about the motor’s power, and especially complimented how steadily it ran. This is an excellent choice for hardwoods, thick softwoods, and composite boards: absolutely anything that’ll fit.
Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. We ranked the quietest 3 saws as a 2, and the remaining saws as a 3 and felt none should rank a 1 due to the need for hearing protection.
The Craftsman table saw is one of the most compact of the bunch when it’s folded up. And if you can get it for the sale price of $260, it’s also the cheapest of the best table saw options. The blade guard and anti-kickback pawls are identical to the Porter-Cable and are the hardest of any of the saws to install. And they are the only two blade guards that don’t have a feature to hold them out of the way when you’re adjusting the blade or setting up the cut.
I build guitars in a small shop; I need my saw to be accurate, repairable and easy to store or move. I love this saw! I use it for everything from cutting down stock to slotting my fretboards. It gets out of the way, it came dead on square, and the dust collection works pretty well with a shop vac and great with a high volume dust collector, with an Incra miter fence it makes perfect, repeatable, and accurate cuts. After I had owned it for over a year the plastic lever on the riving knife broke - I called Bosch and they "goodwilled" me a new riving knife assembly (with an upgraded metal lever) via express mail. No charge and fast, friendly service - they didn't even ask for a serial number or proof of purchase. I'd buy this saw again in a minute - all tools wear out or break at some point and I really like that the company stood behind this one and got me up and running again in a hurry. I also love all the safety features - riving knife, anti-kickback pawls, large easy-to-reach power button, nice push stick, and a dust collection port that is positioned out of the user's way.
It has the widest rip capacity of the three. This one can handle materials up to 32 1/2”, which makes it ideal for folks who work with sheet stock on the go–especially when you consider the extra 22” you’ll have to the left of the blade. That’s thanks to the same rack and pinion fence as the smaller Dewalt. It’s even better on a larger scale, where the differences between this design and the sliding rail style you find on Bosch become very apparent. Reviewers agreed that this one felt much sturdier, smoother, and locked more securely than other portable units.
If you’re a home DIYer or pro working mainly from a shop, you may have a wide table or countertop big enough to use the saw without any accessory stand. We would caution against working on sawhorses, though, as they can be wobbly and unsafe. It’s far better to spend a few extra dollars on a sturdy stand than to take risks with a rickety, improvised setup.
While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.
Table saws will continue to be popular and much sought after tools in any workshop or construction site. There are many terrific styles on the market which is why it is important to do some research and look at the reviews provided here as well as the tips contained in this guide to help you choose the right table saw for your needs, whether you are a professional or a DIYer who loves to work in the workshop making things for enjoyment.
I also added in a bicycle saddle bag, that attaches easily to the tube frame of the saw. In it, I keep my PPE, and my Grr-ripper push blocks (great upgrade over regular push blocks). I also have a push stick made of wood that was modeled after the plastic one mounted on the back of the saw. The wood one is there now. I read too many stories of injuries after the blade touched the plastic stick, which to me is the whole point of using a stick – to avoid injuries. These things turning to shrapnel seems like a bad idea.
If you work with wood in any capacity, chances are you rely on a table saw to make clean, accurate cuts. But when your good old saw goes to the big toolshed in the sky, it’s time to opt for a replacement. Before you dish out your hard-earned money on the first model you come across, remember that a table saw is a big investment, so it’s in your best interest to look into the many technical specifications of each option before you settle on a final purchase.
While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately.
SawStop is the only saw in the group to employ this style fence and they have the best in the group. Ridgid comes in second with a traditional front clamping fence system that has a backside contact point. Its solid construction and wide cast front clamp left us impressed. DeWalt’s came in third with an innovative effort that locks into several points based on where you need it. Rather than sliding along, it stays in place while the rack and pinion system moves it into place. It’s not perfect, but it eliminates a lot of accuracy issues that come from locking the fence out of square on some systems.
The saw itself is remarkably compact, measuring just 22.5″ square and a little over a foot in height (13″ to be more precise). With a steel “roll cage” that encloses the 4 HP 15-amp motor and a rubber handle that is positioned in the center of the right side of the saw, this is a tool that you’ll find very easy to toss into the back of a pickup or work van and take to any jobsite. When you carry it deck-inward, the weight of the saw presses in slightly against your leg – which actually steadies the saw somewhat, making it more manageable, though at 52-pounds let’s not go so far as to call this saw a breeze to carry. The Bosch GTS1031 included cord wrap, and the simple design of the frame also makes it easy to store up against a wall inside your shop when not in use. This isn’t a tool that really gets in the way much – it’s out of sight until it’s needed.
The design is quite good. The SawStop safety system ensures smooth and flawless operation while protecting you from a variety of hazards. However, regardless of the safety aspects, you should always wear protective equipment, especially gloves and goggles. One of the most notable things about the design is the fact that it provides 99 percent dust collection both below and above the table. The riving knife maximizes kickback and also offers protection.
What 🤔?? I find it pretty rare to have to re-align the rack and pinion fence on the dewalt, but short of the first time figuring it out, it shouldn’t take more than 5-10 minutes to do. The time savings comes in not having to stick a tape to the fence every time you move it to ensure it’s parallel. I am excited to see other tool manufacturers are using rack and pinion fences now so that there are other options besides the dewalt, namely skil’s latest worm drive ts and the latest hitachi, I’m just not interested in any other fence system on a job site table saw.
This saw/stand combination is the most expensive of the group. But you get some top-end features. The first thing you’ll notice is the stand with its splayed legs that have no wheels in the setup position. You can’t wheel it around, but man is it sturdy, which is great if you’re ripping sheets of plywood or long, heavy boards. Another unique advantage of this stand is that you can easily remove the saw. That makes the saw easy to transport and to use without the stand. But our favorite feature is the patented rack-and-pinion fence that stays perfectly parallel to the blade and is super easy to adjust. If you can afford to spend a little more, we think the DeWalt is hard to beat.
The only dislike that I have found about the Bosch 4100-09’s operation is that unlocking the table causes a tab to pop up above the cutting surface. This tab interferes with the operation of the fence, and could lead to damage of the product. It also comes with only a one year warranty. It does have available rear out-feed extensions available, to help facilitate larger work pieces.
At a compact 45 pounds, the DEWALT DW745 Compact Jobsite Table Saw is the lightest table saw in our review. The saw's portability doesn't mean that ripping size is compromised, though. Thanks to extending fence guides, you've got 20 inches available. Depth of cut is on par with many bigger machines: at 90 degrees, it's 3 1/8 inches. At 45 degrees, it's 2 1/4 inches. Power comes from a 15-amp motor with a no-load speed of 3,850 RPM. This is ample enough for serious DIY projects and light-duty construction site work.
The Powermatic 1792001K PM2000 is an award winning cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. The 1792001K PM2000 is the result of years of work and research and hundreds of interviews with woodworkers that offered input which was eventually implemented in the saw. The performance, reliably and safety of this saw are so great, that they actually set a new standard by which all other cabinet saws are judged.
Setting up both saws was quick and easy, since their factory-adjusted blades and fences were square and parallel to the tables' miter gauge slots out of the box (this is one of the reasons to buy a $350 table saw over a $100 one). Both saws had similar setup procedures: Attach the fence, raise the riving knife, attach anti-kickback pawls and attach the blade guard. There is no on-board stowage space for the DW745's rip fence, but this does not really affect the setup time or effort by much.
Perfect for both hobbyists and craftsmen, the PCS31230-TGP252 from SawStop is a 3 HP cabinet saw that delivers excellent performance while featuring the company’s patented safety system to ensure maximum safety during use. The safety system is similar to that of the G0690 from Grizzly where the blade stops in milliseconds after it comes in contact with flesh. Designed and built in order to satisfy the needs of the most demanding users, the PCS31230-TGP252 features an exacting finish and feet and a superior dust collection system. For increased precision and added strength, the PCS31230-TGP252 features a fifty two inch T-Glide fence system, but also an extension table and rails.
One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More