6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.
The larger the motor, the higher the voltage as well, usually 240V. In some cases, you may be lucky and have a garage or workshop that’s wired for 240V, so that is why it’s very important that you check this prior to getting the table saw. In terms of the material thickness it can handle, it’s a minimum of three inches. One thing to bear in mind is that safety is an essential consideration with these saws and that’s because the powerful motors are prone to higher kickback.
If you’re looking for the perfect cabinet table saw out there, then you should look no further than the SawStop ICS51230-52. This is an industrial grade cabinet saw and is also the highest quality, most powerful and heaviest cabinet saw you can currently get. Its fifty two inch industrial T-glide fence assembly, combined with a 5 HP, 230V single phase motor offers safety, versatility, durability and peace of mind that SawStop is so well known for.

The Skilsaw SPT70WT-01 is a super high quality table saw with the power to match. The Diablo blade that comes with it will cut through 4×4 without any problems at all, like a knife through butter! One of the best features we noted was the fact that there is barely any vibration, this allows to you to cut as straight as an arrow, you can really feel the build quality with this saw.It has an extremely easy to use miter gauge, just a flick of the wrist to change the angle of cuts to exactly what you want.


6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.
I got the Hitachi 1 1/2 mouths in the motor died. Says it has a 5 year warranty. I’ve been trying for weeks to get it resolved. Ended up giving up and headed to buy another saw. I understand having products be faulty it’s a numbers game it has to happen to some one. How ever the complete no help to resolve it from Hitachi. Is a problem after a week of back and forth they said they would set up a pick up time to ship and get it repaired over a week still no call back for a pick up. I can’t say enough avoid this headache. I’ve been a contractor for a decade and have had may tools break or need repair. First experience I’ve had that’s made me swear off a brand.hope this will save some one from wasting money and time
It’s just as powerful as our other recommendations. The SawStop has a 3HP belt-driven motor, and like the Jet, it uses a tweaked multi-belt drive system to transfer maximum power from the drive shaft to the blade. That makes for as powerful a cabinet saw as any on the market. This one slices smoothly through anything you can feed into it. It also has a slightly thicker max cutting depth than our other recommendations, so it’s the better choice for sturdy stock.
Choosing the best portable jobsite table saw wasn’t an easy task but we’re confident we’ve done a thorough evaluation. In a very close race for the best table saw Hitachi beat out the DEWALT which came in second place followed by Skilsaw in third and Makita in fourth. It’s very interesting that the Hitachi and DEWALT look extremely similar. Hitachi edged out the DEWALT in performance and price resulting in the final scores. Skilsaw beat out Makita for the 3rd place only slightly and that result is really a function of pricing.
Each one has different power, capabilities, mobility and price points as well. If you’re not sure which type you need, we have outline some specifics on each below that will help you choose. When you begin the search for your table saw, you will need to know the answers to a few questions that will narrow down the choices for you and make choosing much easier.

The first thing you should do before starting up your unit is to check whether you’re wearing all the necessary safety equipment. Gloves are something not many people like to wear. Apart from keeping your fingers safe, they also offer protection against thorns. As you may assume, you’ll work with a lot of thorns flying around. However, gloves aren’t mandatory, and they won’t offer much protection apart from occasional thorns.
Table saws are undeniably the kings of rip cuts on the jobsite and in shops. The concept is simple: Place a motor below a solid table to turn a blade somewhere in the 4000-5000 RPM range through the surface and watch the sawdust fly. The idea may be simple, but the reality is much different. How big should the table be? What size blade should you use? How heavy can you get away with making it?
The SKILSAW SPT70WT-01 is truly a woodworking marvel, packing a 15-amp Dual Field motor into a surprisingly lightweight yet durable 49-pound frame. Whether you’re an amateur carpenter or a contractor with years of experience under his toolbelt, SKILSAW’s workhorse of a table saw is an invaluable addition to your repertoire thanks to its raw torque and unparalleled 25" ripping capacity, meaning tearing through thick sheets of plywood has never been easier.
All these saws have attached, collapsible stands with wheels that allow you to roll them around when they’re folded up. A few, like the DeWalt, Rockwell and Ryobi, can’t be wheeled around after they’re set up. But the biggest difference between stands is in how easy it is to set them up. The Ridgid and Bosch have nearly identical stands that work great and require you to only flip or depress one lever to unlock the stand. These are our favorites. The DeWalt stand is the sturdiest of the bunch and very intuitive. It sets up like a card table with legs that fold out and snap into place. The remaining candidates for best table saw have several different stand systems that aren’t quite as easy to set up but that work fine once you get the hang of them.
Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.

Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.
The Bosch 4100-10 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand delivers both professional rip capacity and outstanding portability for a tool that can get the job done, wherever it is. The powerful 15-Amp saw delivers 4.0 max HP for outstanding productivity. It also incorporates soft-start circuitry for smooth but quick ramp-up to the operating speed to manage the intensity of motor start-up and minimize the possibility of tripping a circuit breaker. It includes Constant Response circuitry to help maintain speed under load, and overload protection.
When the blade touches flesh, a brake will stop the blade and the blade drops down below the surface of the table. The operator will presumably leave with only a small nick or no injury at all. These systems definitely bump up the price of the saw, but it’s a major safety feature and just might be able to save you some very expensive medical bills, along with your fingers.
If you are an avid hobbyist, this saw is made just for you. The company is known for its uncompromising quality and durability. This saw has a safety system where the blade stops and retracts automatically when it comes into contact with anything that is not wood.  The microblade guards keep debris from flying all over your workshop. It is easy to change between blades. You will not require a riving knife to do this. Its award-winning dust collection system ensures that you have a clean and presentable workspace at the end of the day.
The Bosch 4100-09 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand delivers both professional rip capacity and outstanding portability for a tool that can get the job done, wherever it is. The powerful 15-Amp saw delivers 4.0 max HP for outstanding productivity. It also incorporates soft-start circuitry for smooth but quick ramp-up to the operating speed to manage the intensity of motor start-up and minimize the possibility of tripping a circuit breaker.. It includes Constant Response circuitry to help maintain speed under load, and overload protection. The Square Lock rip fence is engineered for maximum trueness and great ease-of-use, with the fence able to easily glide along the rail for one-handed operation. The lighter GTA47W Gravity-Rise Wheeled Stand has 8 In. treaded rubber-composite tires and a single-action design for easy set-up and transport. It is jobsite-ready with heavy-duty construction. The Smart Guard System is the first modular table saw blade guard, featuring a three-position adjustable riving knife, anti-kickback pawls and non-obstructed-view barrier guard assembly. The table saw provides a 29 In. x 21-1/2 In. square tabletop with a 25 In. rip capacity for ripping 4 Ft. wide sheets goods in half.
A table saw has two main ways it can seriously hurt you. One is obvious and that is having any part of your body come into contact with the blade. Any table saw you are seriously considering should have a blade guard installed. The clearer the better. And make sure you leave it on. The blade guard can’t do its intended job from a workbench or shelf.
The blade guard is the most noticeable and the most important safety element of every saw. Its purpose is very simple – it keeps your fingers away from the blade. Many people decide to unscrew this part and take it off to speed up the cutting process, but that’s a huge mistake. In fact, a massive percent of injuries happen because people alter the safety mechanisms in order to work faster. Risking your life for a few hours of effective work isn’t worth it, to say the least.
Setting up both saws was quick and easy, since their factory-adjusted blades and fences were square and parallel to the tables' miter gauge slots out of the box (this is one of the reasons to buy a $350 table saw over a $100 one). Both saws had similar setup procedures: Attach the fence, raise the riving knife, attach anti-kickback pawls and attach the blade guard. There is no on-board stowage space for the DW745's rip fence, but this does not really affect the setup time or effort by much. 

How big a table saw is, is determined by the largest blade the saw will hold. 8” blades are the smallest that should be used for any home workshop. You can get blades in 9”, 10”, and 12” sizes as well. Most workshops will not really need the 12” blade as this has a very deep cut capability, but for construction firms and larger, commercial shops, the 12” comes in handy.
The SawStop Contractor Saw CNS175-TGP36 stands out chiefly on account of its unique safety brake, which stops the spinning blade dead when it senses the presence of skin. However, it's also an excellent saw in other respects: powerful, well built, and easy to assemble, with great dust collection and loads of features. Cost is a major concern, but so is the cost of the injuries SawStop is designed to eliminate.
Bengt – We appreciate the feedback as it always helps us get better. Having said that I think some of your concerns were evaluated and included in the results in ways that may not be entirely clear. We adjusted each saw after checking the blade/fence measurements and had no issues getting them adjusted (I may add some text to reinforce that in the article). We don’t do long term testing in this type of article as it’s simply not feasible…so making a statement about whether the saw holds those adjustments isn’t feasible. We evaluated the fences and ranked them in the ergonomics section, we even did lateral load testing on them as part of that ranking.
Move the wood to and then "through" the spinning saw blade slowly and steadily. It's alright to use your hands while you're still at least a foot or so from the blade, but once the end of the board or sheet nears the blade, you should use a pushing stick to keep the wood moving and to keep your fingers away from the blade. Even an experienced carpenter can have a lapse in concentration or a slip that can lead to serious injury.
It’s highly portable. The Dewalt is available with a folding stand, which makes it extremely easy to pack up. The guard assembly lies flat, and the fence can be retracted all the way to the table to keep everything neat and tidy. It’s pretty light, too-at just 45 pounds. We also love that the adjustment tools, accessories like the miter gauge, and even the guard components can be stored inside the saw for transport, or when they’re not being used.

I’m no stranger to Bosch’s 4100-09 saw with Gravity-Rise™ stand. I’ve used one several times to build projects for this magazine, including the Serving Tray Cart that appeared in the June issue. So, I was not surprised when it tested impressively here. Rip cuts were on the mark, thanks to a rugged, beefy fence that stayed parallel to the blade each time I reset it. A flip of a red lever underneath unlocks the rails so they slide out and extend ripping capacity up to 25″.


If you’re going to be transporting your unit regularly, you should aim to keep weight to a minimum. Look for something lightweight, with convenient carrying handles, or a stand that can be wheeled around dolly-style at the worksite. Conversely, if you’re only going to be using your portable saw occasionally, you can probably stand a bit more weight.
The only dislike that I have found about the Bosch 4100-09’s operation is that unlocking the table causes a tab to pop up above the cutting surface. This tab interferes with the operation of the fence, and could lead to damage of the product. It also comes with only a one year warranty. It does have available rear out-feed extensions available, to help facilitate larger work pieces.
I’m no stranger to Bosch’s 4100-09 saw with Gravity-Rise™ stand. I’ve used one several times to build projects for this magazine, including the Serving Tray Cart that appeared in the June issue. So, I was not surprised when it tested impressively here. Rip cuts were on the mark, thanks to a rugged, beefy fence that stayed parallel to the blade each time I reset it. A flip of a red lever underneath unlocks the rails so they slide out and extend ripping capacity up to 25″.
Besides that, materials are expensive, and when you ruin even a couple of pricey work pieces with a saw that doesn’t provide accurate cut you will end up paying far more for that cheap saw than you anticipated. Having a good saw that you can depend on for accuracy and efficiency is a solid business move for any contractor. Both the DW745 and the Bosch 4100 have a true riving knife, anti-kickback pawls, and a blade guard to prevent kickback and possible injury.
Bengt – We appreciate the feedback as it always helps us get better. Having said that I think some of your concerns were evaluated and included in the results in ways that may not be entirely clear. We adjusted each saw after checking the blade/fence measurements and had no issues getting them adjusted (I may add some text to reinforce that in the article). We don’t do long term testing in this type of article as it’s simply not feasible…so making a statement about whether the saw holds those adjustments isn’t feasible. We evaluated the fences and ranked them in the ergonomics section, we even did lateral load testing on them as part of that ranking.
Table saws are undeniably the kings of rip cuts on the jobsite and in shops. The concept is simple: Place a motor below a solid table to turn a blade somewhere in the 4000-5000 RPM range through the surface and watch the sawdust fly. The idea may be simple, but the reality is much different. How big should the table be? What size blade should you use? How heavy can you get away with making it?
The saw’s table measures 29 x 21.5 inches which makes this unit suitable for the fabrication of large sheets of material and large wood stock. The table is made out of aluminum and is really smooth which means you will be able to slide even the largest pieces in with very little effort. Still, for extra safety, I would recommend the optional extensions when ripping longer workpieces.

As with the smaller Dewalt we’ve recommended, this one has very inconsistent quality control on the table. Some reviewers cited units with bowed, funky surfaces, while others got units that were perfectly flat. that’s a flaw of the molding process. We also have a bone to pick with Dewalt as far as the coating on these. While we understand that the coating is supposed to help wood slide better, it just doesn’t seem to last very long or hold up well. It also has the same flawed warranty coverage. We’d recommend purchasing add-on coverage.

As far as performance, the fence could be a bit better in its locking in – square front to rear – but you get used to being able to set it square and use the rear adjustment knob so that it stays put. Some folks have complained about motor burn outs – but having experience now with 17 saws – over 6 years or more – I haven’t encountered the problem (maybe we’ve been lucky?)
The service coverage under the warranty requires you to either bring the machine to an authorized dealer or ship it back to the company on your dollar. That’s a major downside, and it’s one reason we’re recommending purchasing add-on warranty coverage for this one. If you’re dealing with a third party provider, you can simply get a replacement without having to go through frustrating company reps.
After spending hours doing a lot of research and talking to professionals who use these tools on a regular basis we have put together a review for you that not only tells you three of the top table saws on the market today, but we tell you why they are popular and explain a bit about each so you have a good idea of what they are like. This table saw review will put much-needed information right at your fingertips so you can make a good decision on the right table saw for your needs.
If you want a table saw that helps you deliver products faster, the Bosch 4100-09 could be what you’ve been waiting for. It has a Gravity-Rise stand that is built for efficient and accurate setup and takes down.The portable construction makes it easy to bring to any worksite with minimal trouble. Only weighing 39 pounds, you will have no problem transporting this table saw wherever you need to go. The Bosch 4100-09 is a powerful saw that is made for the kind of high precision cutting that professionals and DIYers are looking for. It has a 15 AMP, 4 HP motor that generates 3,650 RPMs for clean cuts every time.
Ridgid notches a third place finish as the only saw to include an independent blade height lock. The adjustment wheel raises and lowers with multiple full turns like most saws, but integrates a lock into the center. For the bevel adjustment, the outside of the height adjustment wheel turns a rack and pinion style system to accurately change the blade angle – a feature Makita shares.
The DEWALT DW745 and the Bosch 4100 are pretty evenly matched in having plenty of power and not-so-hot dust collection. I you’re looking for a light weight saw, the DEWALT comes in ahead since it weighs almost half as much as the Bosch. It is also the less expensive choice by far. The large work table, expanded cutting capability, and its Gravity Rise feature (with solid rubber wheels that make it easy to be rolling across rugged terrain at a jobsite) make the Bosch a Cadillac among Pintos, but, of course, that luxury comes with a price tag.
One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More
×